Wednesday, August 13, 2014

How To Replace Hyundai Sonata Fuel Pump Replacement 2004 - 2010

2004-2010 Hyundai Sonata Fuel Pump Replacement

This blog is not responsible for any damages or injuries caused by following these steps

Tools needed:
- Hammer
- couple flat head screw drivers
- phillips screw driver

Deprime the fuel line and disconnect the battery for safety. 


GOOD NEWS YOU DO NOT HAVE TO DROP THE TANK.

I recommend using Delphi fuel pump with lifetime warranty from Autozone. I have never had to replace another one since using them. 

 First open the trunk and pull the carpet cover off.


You will see the cover for the fuel tank in the very back of the trunk.


It can also be accessed from inside the car behind the rear passenger side seat. 


Remove the 4 philips screws holding the cover plate over the fuel pump.


Once the plate is removed you will see the top of the tank and the fuel pump does not line up directly to the hole but it will fit through.


You will need to unplug the 2 plugs to get the plate out of the way. 



Next you will need to remove the 2 fuel lines 
the one with the green clip push in on the front part of the clip and it will slid off. 


The orange clip you must first slide the orange clip back.
Next push in on the yellow tabs on both sides and pull up. 



once the hoses and plugs have been removed, clean the area around to keep from contaminants falling into the tank. 
Then use a screwdriver and a hammer to tap off the ring around the fuel pump. 
It is recommended to use a brass hammer and chisel for this to prevent sparks. 
The ring will turn counter clockwise to screw off, by pounding on these areas.


If rusted out to badly you can purchase a new one at Autozone

Once the ring is off you can begin pulling the fuel pump out 
by turning and twisting it will eventually come out.
Be careful not to mess up the fuel level sensor. 
Also be careful not to lose the o ring down in the tank as well, 
and when reinstalling make sure the
 o ring is seated properly at the top of the tank. 


With the pump out now you must pull the pump assembly apart to replace the pump itself. 

First, unplug the 2 plugs on the bottom side of the top of the pump assembly.


Next, remove the clip holding this part onto the assembly.


Now go around with a screwdriver and pop off the outer shell of the fuel pump assembly.




I used a flat head Craftsmen screw driver to pry out and up to pop the 3 taps out.


You will then end up with 2 separate parts. 


Now the very bottom of the inside part has 4 clips that also must be popped out in order to get the fuel pump out. 

Again use a flathead screwdriver in order to remove the cap.


Once removed the fuel pump will come right out.



The last thing you will need to pull the strainer off the bottom of the pump.
it is removed by simply pulling it down and it will slid off. 
It is recommended to replace this strainer as well. It also can be found at your local Autozone store.  



Repeat all these steps in reverse to put it all back together. 


Tuesday, January 28, 2014

How to replace the alternator on a 2001-2004 Ford escape v6 the easy way

How to remove the alternator in a 2001-2004 Ford Escape the easy way. 
Tools needed
Jack Jack stands
3/8 ratchet
8mm socket
10mm socket
13mm socket
extention
pliers 
philips screw driver
Lug nut remover

First thing disconnect the battery using 8mm socket. 
Step by step on how to remove the battery

Next jack the escape up on the passenger side and place jack stand under for safety.

Remove the passenger wheel 


 Here you will find 2 10mm bolts and 1 phillips screw that must be removed to gain acess to where the alternator and pullys are



Also on the bottom of the escape near the front the plastic cover continues
 under the car it is removed with 3 10mm bolts 


 Once the plastic removed you will now see the alternator. 

Now we need  to remove the belt off the alternator
find the tensioner and use a 3/8 drive ratchet to loosen the tensioner as you remove the belt.

I was unable to get clear pictures of the alternator 
but there are 3 13mm bolts holding the alternator onto the engine.
There are also a plug and one wire bolted on by a 10mm nut.

 once all is disconnected and unplugged the fastest way to get this off is to go straight up the top. 

To make room you must unbolt the computer and and unplug it, and disconnect the following hoses

Next you must remove the oval canister below it. 
It is removed by 2 10mm bolts and there are 2 hoses that must be disconnect from it. 
Simply just pull on the hoses to disconnect them.
also unplug the 2 plugs near the hoses. 


One more plug down deep between the firewall and engine is a green plug that must be unplugged and pulled to the side. 

now you are ready to fish the alternator starit from the bottom all the way to the top between the firewall and engine. 

It is a tight fit but wiggle and move around and it will eventually make its way up. 

Easiest way i found to pull it up is pully facing up. 

once you pulled the alternator up and out you simply place the new one back down and reverse the steps above. 

Thank you and if you have any questions leave a comment below.
Follow me for more DIY auto repair projects. 

How to remove and replace the battery in 2001-2010 Ford Escape

How to Replace the Battery in a 2001-2010 Ford Escape 

Tools needed
10mm flat wrench
8mm Flat wrench


With an 8mm flat wrench disconnect the terminals by loosening these two bolts.
they only need to be loosened until the terminals will slide off. 

Now with a 10mm flat wrench loosen the 2 nuts on the strap holding the battery down. 
They do not need to be removed completely just enough where it is loose enough unhook it from the battery box tray. 

Here you can see where to unhook the strap. 

Remove the battery and install the new battery in reverse order.

Thank you for using us as your guide 
Follow us for more DIY car repairs. 

Thursday, January 23, 2014

How to check / fill WV Jetta / Golf 97-00 automatic transmission fluid.

How to check transmission fluid in a VW Jetta 


You will need the following tools

Ratchet
17mm socket
Ramps/ Jack, jackstands
T-30 star socket
Oil pump that connects to oil jugs

First Put the car up on Ramps or jacks

Next locate the bottom of the transmission on the drivers side. A metal shield is covering the bottom of the transmission and must be removed. 

To remove the shield you must remove 4 - 17mm bolts, 2 on each side. 


With the cover removed you will see the Red cap over the fill spout. 

To remove the cap you must push in on the metal clip.

You must then remove the star t-30 bolt to the left of  the filler tube. 

Use your oil pump and fill with transmission fluid until it comes out of the star bolt hole. 

Once the oil begins coming out as shown below you will know you have the proper fluid level.

Reinstall everything as it was removed and your ready to cruse. 

I recommend only using VW Transmission Fluid only.
I picked mine up at www.carparts.com. It is not cheap but if 
you want your transmission to run as it should use OEM fluid. 

The oil pump that we used can be found at Autozone

 Thank you for checking out this blog.
I hope i have helped you today.